The Famous Joule Thief

Here is a electronic circuit that anyone can build at a minimal cost. From what I have seen on the Internet there are many different applications that you can expand on using the Joule Thief as the key component to your experiments.

One video used the circuit with the battery disconnected, now I did not see how long the circuit ran but as the power seemed to be coming from the discharge of a capacitor in the circuit.

The following is a description From Wikipedia.

The circuit works by rapidly switching the transistor. Initially, current enters the transistor base terminal (through the resistor and secondary winding), causing it to begin conducting collector current through the primary winding. This induces a voltage in the secondary winding (positive, because of the winding polarity, see dot convention) which turns the transistor on harder. This self-stoking/positive-feedback process almost instantly turns the transistor on as hard as possible (putting it in the saturation region), making the collector-emitter path look like essentially a closed switch (since VCE will be only about 0.1 volts, assuming that the base current is high enough). With the primary winding effectively across the battery, the current increases at a rate proportional to the supply voltage divided by the inductance. Switch-off of the transistor takes place by different mechanisms dependent upon supply voltage.
The predominant mode of operation relies on the non-linearity of the inductor (this does not apply to air core coils). As the current ramps up it reaches a point, dependent upon the material and geometry of the core, where the ferrite saturates (the core may be made of material other than ferrite). The resulting magnetic field stops increasing and the current in the secondary winding is lost, depriving the transistor of base drive and the transistor starts to turn off. The magnetic field starts to collapse, driving current in the coil into the light emitting diode (raising the voltage until conduction occurs) and the reducing magnetic field induces a reverse current in the secondary, turning the transistor hard off.
At lower supply voltages a different mode of operation takes over: The gain of a transistor is not linear with VCE. At low supply voltages (typically 0.75v and below) the transistor requires a larger base current to maintain saturation as the collector current increases. Hence, when it reaches a critical collector current, the base drive available becomes insufficient and the transistor starts to pinch off and the previously described positive feedback action occurs turning it hard off.
To summarize, once the current in the coils stops increasing for any reason, the transistor goes into the cutoff region (and opens the collector-emitter "switch"). The magnetic field collapses, inducing however much voltage is necessary to make the load conduct, or for the secondary-winding current to find some other path.
When the field is back to zero, the whole sequence repeats; with the battery ramping-up the primary-winding current until the transistor switches on.
If the load on the circuit is very small the rate of rise and ultimate voltage at the collector is limited only by stray capacitances, and may rise to more than 100 times the supply voltage. For this reason, it is imperative that a load is always connected so that the transistor is not damaged. Note that, because VCE is mirrored back to the secondary, failure of the transistor due to a small load will occur through the reverse VBE limit for the transistor being exceeded (this occurs at a much lower value than VCEmax).
The transistor dissipates very little energy, even at high oscillating frequencies, because it spends most of its time in the fully on or fully off state, thus minimizing the switching losses.
The switching frequency in the example circuit opposite is about 50 kHz. The light-emitting diode will blink at this rate, but the persistence of the human eye means that this will not be noticed.[1]


A simple shunt-regulator for loads requiring a constant voltage
When a more constant output voltage is desired, a voltage regulator can be added to the output of the first schematic. In this example of a simple shunt-regulator, a blocking diode ("D_rect") allows the secondary winding to charge a filter capacitor ("C_filter") but prevents the transistor from discharging the capacitor. A Zener diode ("Z1") is used to limit the maximum output voltage.

Here is a site where you can get step by step instructions on how to build one of these amazing little devices. http://www.instructables.com/id/Make-a-Joule-Thief/

Until next time keep on keeping on.